UB Paderborn / Katalog / Suche / in CDI

1 – 25 von 272

Sortiert nach

Experimental investigations of machining characteristics on polydimethylsiloxane (PDMS) by cryogenic abrasive air-jet machining

International journal of advanced manufacturing technology, 2022-02, Vol.118 (7-8), p.2711-2723

2022

Link zum Volltext

Verfügbarkeit prüfen

Prediction of erosion volume of PDMS by cryogenic micro-abrasive jet machining based on dimensional analysis method and experimental verification

International journal of advanced manufacturing technology, 2021-06, Vol.114 (7-8), p.2447-2455

2021

Link zum Volltext

Verfügbarkeit prüfen

A machining position optimization approach to workpiece deformation control for aeronautical monolithic components

International journal of advanced manufacturing technology, 2020-07, Vol.109 (1-2), p.299-313

2020

Link zum Volltext

Verfügbarkeit prüfen

Experimental study on machining germanium wafer with ice particle, fixed abrasive tools

International journal of advanced manufacturing technology, 2021-08, Vol.115 (9-10), p.3225-3232

2021

Link zum Volltext

Verfügbarkeit prüfen

Influence of tool offset on microstructure and properties of Mg/Al dissimilar alloys by friction stir welding joints at low heat input

International journal of advanced manufacturing technology, 2020-08, Vol.109 (9-12), p.2845-2853

2020

Link zum Volltext

Verfügbarkeit prüfen

Influences on the extended length and performance of push bending for the GH4169 superalloy tube with small bending radius of 1D

International journal of advanced manufacturing technology, 2021, Vol.112 (1-2), p.107-119

2021

Link zum Volltext

Verfügbarkeit prüfen

A workpiece stability-based iterative planning of clamping forces for fixturing layout specification of a complex workpiece

International journal of advanced manufacturing technology, 2019-08, Vol.103 (5-8), p.2017-2035

2019

Link zum Volltext

Verfügbarkeit prüfen

Development of erosion equations for removal of organic coating on carbon fiber reinforced polymer surface by plastic abrasive

JCT research, 2023-03, Vol.20 (2), p.671-685

2023

Link zum Volltext

Verfügbarkeit prüfen

Study on EDM technology of distributed group electrodes in titanium alloy with large inclined angle and thin-walled group holes

International journal of advanced manufacturing technology, 2021-03, Vol.113 (1-2), p.131-140

2021

Link zum Volltext

Verfügbarkeit prüfen

Study on the improvement of the surface integrity and efficiency of electrical-discharge-machined TC4 titanium alloy via abrasive flow machining

Proceedings of the Institution of Mechanical Engineers. Part B, Journal of engineering manufacture, 2021-05, Vol.235 (6-7), p.1197-1211

2021

Link zum Volltext

Verfügbarkeit prüfen

Investigation on Cotes-formula-based prediction method and its experimental verification of milling stability

Journal of manufacturing processes, 2021-04, Vol.64, p.1077-1088

2021

Link zum Volltext

Verfügbarkeit prüfen

Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting

Materials, 2024-03, Vol.17 (7), p.1523

2024

Link zum Volltext

Verfügbarkeit prüfen

Effect of Pore Defects on Mechanical Properties of Graphene Reinforced Aluminum Nanocomposites

Metals (Basel ), 2020-04, Vol.10 (4), p.468

2020

Link zum Volltext

Verfügbarkeit prüfen

Design of surface grooves on a polishing pad based on slurry uniform flow

International journal of advanced manufacturing technology, 2019-08, Vol.103 (9-12), p.4795-4803

2019

Link zum Volltext

Verfügbarkeit prüfen

Grinding characteristics in high-speed grinding of boron-diffusion-hardened TC21-DT titanium alloy with vitrified CBN wheel

International journal of advanced manufacturing technology, 2017-03, Vol.89 (5-8), p.1269-1277

2017

Link zum Volltext

Verfügbarkeit prüfen

Effects of anode layer linear ion source on the microstructure and mechanical properties of amorphous carbon nitride films

Surface & coatings technology, 2017-06, Vol.320, p.183-189

2017

Link zum Volltext

Verfügbarkeit prüfen

Cutting parameters optimization and cutting performance of Ti(C,N)-based cermets by reactive hot-pressing from Co–Ti–C–BN system in dry turning austenitic stainless steels

Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2023-05, Vol.45 (5), Article 266

2023

Link zum Volltext

Verfügbarkeit prüfen

Experimental evaluation for internal trapezoidal thread with axial ultrasonic vibration cutting of Ti–6Al–4V

Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2020-05, Vol.42 (5), Article 247

2020

Link zum Volltext

Verfügbarkeit prüfen

Hot corrosion behaviour of low Al NiCoCrAlY cladded coatings reinforced by nano-particles on a Ni-base super alloy

Corrosion science, 2010-10, Vol.52 (10), p.3561-3567

2010

Link zum Volltext

Verfügbarkeit prüfen

An Assembly Man-Hour Estimation Model Based on GA-SVM for Multi-specification and Small-Batch Production

Transactions of Nanjing University of Aeronautics & Astronautics, 2023-01, Vol.40 (4), p.500

2023

Link zum Volltext

Verfügbarkeit prüfen

Cutting performance of cubic boron nitride-coated tools in dry turning of hardened ductile iron

Journal of manufacturing processes, 2020-08, Vol.56, p.158-168

2020

Link zum Volltext

Verfügbarkeit prüfen

Effect of deposition parameters on crystalline of CVD diamond

Integrated ferroelectrics, 2019-03, Vol.197 (1), p.133-138

2019

Link zum Volltext

Verfügbarkeit prüfen

Effect of Pre-Strain on Microstructure and Tensile Properties of Ti-6Al-4V at Elevated Temperature

Metals (Basel ), 2021-08, Vol.11 (8), p.1321

2021

Link zum Volltext

Verfügbarkeit prüfen

In situ production of ultra-fine Ti(C,N)–TiB2–Co cermets by reactive hot processing from the Co–Ti–C–BN system

International journal of refractory metals & hard materials, 2016-02, Vol.55, p.1-10

2016

Link zum Volltext

Verfügbarkeit prüfen

The effect of various Co contents on the microstructure and properties of Ti(C,N)-TiB2-Co cermets prepared in situ via reactive hot pressing

Advances in mechanical engineering, 2020-05, Vol.12 (5)

2020

Link zum Volltext

Verfügbarkeit prüfen

1 – 25 von 272

Suche als RSS-Feed

Suchergebnisse filtern

Filter anzeigen

Nur zeigen

Geprüft (Peer-Review)
(228)
Mit Volltextzugriff
(266)

Publikationsform

Sprache

Erscheinungsjahr

n.n

Thema

Science & Technology
(210)
Technology
(196)
Engineering
(152)
Materials Science
(116)
Engineering, Manufacturing
(108)
Materials Science, Multidisciplinary
(101)
Engineering, Mechanical
(83)
Manufacturing Engineering
(62)
Materials & Manufacturing Processes
(62)
Physical Sciences
(54)
Physics
(38)
Mechanical Engineering
(35)
Physics, Applied
(33)
Automation & Control Systems
(32)
Industrial And Production Engineering
(30)
Original Article
(30)
Physics, Condensed Matter
(30)
Cae) And Design
(29)
Computer-Aided Engineering (cad
(29)
Media Management
(29)

15 weitere anzeigen...

Weniger anzeigen...

Neu hinzugefügt

... seit 30 Tagen
(1)

Menü

Weitere Dienste

Einstellungen

Experimental investigations of machining characteristics on polydimethylsiloxane (PDMS) by cryogenic abrasive air-jet machining

Prediction of erosion volume of PDMS by cryogenic micro-abrasive jet machining based on dimensional analysis method and experimental verification

A machining position optimization approach to workpiece deformation control for aeronautical monolithic components

Experimental study on machining germanium wafer with ice particle, fixed abrasive tools

Influence of tool offset on microstructure and properties of Mg/Al dissimilar alloys by friction stir welding joints at low heat input

Influences on the extended length and performance of push bending for the GH4169 superalloy tube with small bending radius of 1D

A workpiece stability-based iterative planning of clamping forces for fixturing layout specification of a complex workpiece

Development of erosion equations for removal of organic coating on carbon fiber reinforced polymer surface by plastic abrasive

Study on EDM technology of distributed group electrodes in titanium alloy with large inclined angle and thin-walled group holes

Study on the improvement of the surface integrity and efficiency of electrical-discharge-machined TC4 titanium alloy via abrasive flow machining

Investigation on Cotes-formula-based prediction method and its experimental verification of milling stability

Experimental Investigation on Magnetic Abrasive Finishing for Internal Surfaces of Waveguides Produced by Selective Laser Melting

Effect of Pore Defects on Mechanical Properties of Graphene Reinforced Aluminum Nanocomposites

Design of surface grooves on a polishing pad based on slurry uniform flow

Grinding characteristics in high-speed grinding of boron-diffusion-hardened TC21-DT titanium alloy with vitrified CBN wheel

Effects of anode layer linear ion source on the microstructure and mechanical properties of amorphous carbon nitride films

Cutting parameters optimization and cutting performance of Ti(C,N)-based cermets by reactive hot-pressing from Co–Ti–C–BN system in dry turning austenitic stainless steels

Experimental evaluation for internal trapezoidal thread with axial ultrasonic vibration cutting of Ti–6Al–4V

Hot corrosion behaviour of low Al NiCoCrAlY cladded coatings reinforced by nano-particles on a Ni-base super alloy

An Assembly Man-Hour Estimation Model Based on GA-SVM for Multi-specification and Small-Batch Production

Cutting performance of cubic boron nitride-coated tools in dry turning of hardened ductile iron

Effect of deposition parameters on crystalline of CVD diamond

Effect of Pre-Strain on Microstructure and Tensile Properties of Ti-6Al-4V at Elevated Temperature

In situ production of ultra-fine Ti(C,N)–TiB2–Co cermets by reactive hot processing from the Co–Ti–C–BN system

The effect of various Co contents on the microstructure and properties of Ti(C,N)-TiB2-Co cermets prepared in situ via reactive hot pressing

Suchergebnisse filtern