UB Paderborn / Katalog / Suche / in CDI

1 – 11 von 11

Sortiert nach

XRD and XPS studies on surface MMC layer of SiC reinforced Ti–6Al–4V alloy

Journal of materials processing technology, 2003-12, Vol.142 (3), p.725-737

2003

Volltextzugriff (PDF)

XRD and XPS studies of surface MMC layers developed by laser alloying Ti–6Al–4V using a combination of a dilute nitrogen environment and SiC powder

Surface & coatings technology, 2006-10, Vol.201 (3), p.724-736

2006

Volltextzugriff (PDF)

Considering RFID Inmate Tagging Application to Enhance Prison Management

2006 IEEE International Conference on Semiconductor Electronics, 2006, p.253-257

2006

Volltextzugriff (PDF)

Challenges in Implementing RFID Tag in a Conventional Library

2006 IEEE International Conference on Semiconductor Electronics, 2006, p.258-262

2006

Volltextzugriff (PDF)

Adaptive output-based command shaping for sway control of a 3D overhead crane with payload hoisting and wind disturbance

Mechanical systems and signal processing, 2018-01, Vol.98, p.157-172

2018

Volltextzugriff (PDF)

Efficient control of a 3D overhead crane with simultaneous payload hoisting and wind disturbance: design, simulation and experiment

Mechanical systems and signal processing, 2020-11, Vol.145, p.106893, Article 106893

2020

Volltextzugriff (PDF)

Tool Wear and Surface Roughness when Machining AlSi/AlN Metal Matrix Composite Using Uncoated Carbide Cutting Tool

Materials science forum, 2014-01, Vol.773-774, p.409-413, Article 409

2014

Volltextzugriff (PDF)

Effect of fly ash particle reinfo rcement on microstructure, porosity and hardness in Al-(Si-Mg) cast composites

ASEAN journal on science & technology for development, 2017-10, Vol.23 (1&2), p.113-122

2017

Volltextzugriff (PDF)

Chip Formation in the Machining of Al-Si/10% AlN Metal Matrix Composite by using a TiN-coated Carbide Tool

Research Journal of Applied Sciences, Engineering and Technology, 2016-09, Vol.13 (6), p.422-426

2016

Volltextzugriff (PDF)

Tool Wear in Machining AlSi/AlN Metal Matrix Composite 10 Wt% Reinforcement Using Uncoated Cutting Tool

Applied Mechanics and Materials, 2014-01, Vol.465-466, p.973-977

2014

Volltextzugriff (PDF)

post harvest sensory and chemical characteristics of cold-stored pineapples pretreated with different Fruitone concentrations

Journal of the science of food and agriculture, 2006-10, Vol.86 (13), p.2067-2075

2006

Volltextzugriff (PDF)

1 – 11 von 11

Suche als RSS-Feed

Suchergebnisse filtern

Filter anzeigen

Nur zeigen

Geprüft (Peer-Review)
(8)
Mit Volltextzugriff
(11)

Publikationsform

Artikel
(9)
Tagungsberichte
(2)

Sprache

Englisch
(11)
Japanisch
(1)

Erscheinungsjahr

n.n

Kollektion

2 weitere anzeigen...

Weniger anzeigen...

Menü

Weitere Dienste

Einstellungen

XRD and XPS studies on surface MMC layer of SiC reinforced Ti–6Al–4V alloy

XRD and XPS studies of surface MMC layers developed by laser alloying Ti–6Al–4V using a combination of a dilute nitrogen environment and SiC powder

Considering RFID Inmate Tagging Application to Enhance Prison Management

Challenges in Implementing RFID Tag in a Conventional Library

Adaptive output-based command shaping for sway control of a 3D overhead crane with payload hoisting and wind disturbance

Efficient control of a 3D overhead crane with simultaneous payload hoisting and wind disturbance: design, simulation and experiment

Tool Wear and Surface Roughness when Machining AlSi/AlN Metal Matrix Composite Using Uncoated Carbide Cutting Tool

Effect of fly ash particle reinfo rcement on microstructure, porosity and hardness in Al-(Si-Mg) cast composites

Chip Formation in the Machining of Al-Si/10% AlN Metal Matrix Composite by using a TiN-coated Carbide Tool

Tool Wear in Machining AlSi/AlN Metal Matrix Composite 10 Wt% Reinforcement Using Uncoated Cutting Tool

post harvest sensory and chemical characteristics of cold-stored pineapples pretreated with different Fruitone concentrations

Suchergebnisse filtern