UB Paderborn / Katalog / Suche / in CDI

1 – 25 von 98

Sortiert nach

Assessment and Comparison of Various MCDM Approaches in the Selection of Manufacturing Process

Advances in materials science and engineering, 2020, Vol.2020 (1)

2020

Volltextzugriff (PDF)

Enhanced Solubility of the Support in an FDM-Based 3D Printed Structure Using Hydrogen Peroxide under Ultrasonication

Advances in materials science and engineering, 2018-01, Vol.2018 (1)

2018

Volltextzugriff (PDF)

Extrusion-Based 3D Printing of Microfluidic Devices for Chemical and Biomedical Applications: A Topical Review

Micromachines (Basel), 2018-07, Vol.9 (8), p.374

2018

Volltextzugriff (PDF)

Semi-analytical models for non-Newtonian fluids in tapered and cylindrical ducts, applied to the extrusion-based additive manufacturing

Materials & design, 2022-11, Vol.223, p.111168, Article 111168

2022

Volltextzugriff (PDF)

Fused filament fabrication of commercial conductive filaments: experimental study on the process parameters aimed at the minimization, repeatability and thermal characterization of electrical resistance

International journal of advanced manufacturing technology, 2020-12, Vol.111 (9-10), p.2971-2986

2020

Volltextzugriff (PDF)

Additive Manufacturing for Soft Robotics: Design and Fabrication of Airtight, Monolithic Bending PneuNets with Embedded Air Connectors

Micromachines (Basel), 2020-05, Vol.11 (5), p.485

2020

Volltextzugriff (PDF)

Mechanobiological Approach to Design and Optimize Bone Tissue Scaffolds 3D Printed with Fused Deposition Modeling: A Feasibility Study

Materials, 2020-02, Vol.13 (3), p.648

2020

Volltextzugriff (PDF)

Analytical and Numerical Models of Thermoplastics: A Review Aimed to Pellet Extrusion-Based Additive Manufacturing

Polymers, 2021-09, Vol.13 (18), p.3160

2021

Volltextzugriff (PDF)

Thermal Characterization of New 3D-Printed Bendable, Coplanar Capacitive Sensors

Sensors (Basel, Switzerland), 2021-09, Vol.21 (19), p.6324

2021

Volltextzugriff (PDF)

Enhancing the sensitivity of 3D printed sensors via ironing and void reduction

Virtual and physical prototyping, 2024-12, Vol.19 (1)

2024

Volltextzugriff (PDF)

Experimental investigation on camera calibration for 3D photogrammetric scanning of micro-features for micrometric resolution

International journal of advanced manufacturing technology, 2017-08, Vol.91 (9-12), p.2935-2947

2017

Volltextzugriff (PDF)

On the Impact of the Fabrication Method on the Performance of 3D Printed Mixers

Micromachines (Basel), 2019-04, Vol.10 (5), p.298

2019

Volltextzugriff (PDF)

Manufacturing-oriented review on 3D printed lithium-ion batteries fabricated using material extrusion

Virtual and physical prototyping, 2023-12, Vol.18 (1)

2023

Volltextzugriff (PDF)

Bioengineering Bone Tissue with 3D Printed Scaffolds in the Presence of Oligostilbenes

Materials, 2020-10, Vol.13 (20), p.4471

2020

Volltextzugriff (PDF)

Correlation of Process Parameters with Mechanical Properties of Laser Sintered PA12 Parts

Advances in materials science and engineering, 2017-01, Vol.2017, p.1-11

2017

Volltextzugriff (PDF)

Fused Filament Fabrication (FFF) for Manufacturing of Microfluidic Micromixers: An Experimental Study on the Effect of Process Variables in Printed Microfluidic Micromixers

Micromachines (Basel), 2021-07, Vol.12 (8), p.858

2021

Volltextzugriff (PDF)

Additive manufacturing aimed to soft robots fabrication: A review

Extreme Mechanics Letters, 2021-01, Vol.42, p.101079, Article 101079

2021

Volltextzugriff (PDF)

Additive Manufacturing for Sensors: Piezoresistive Strain Gauge with Temperature Compensation

Applied sciences, 2022-09, Vol.12 (17), p.8607

2022

Volltextzugriff (PDF)

Computer Numerical Controlled Grinding and Physical Vapor Deposition for Fused Deposition Modelled Workpieces

Advances in materials science and engineering, 2018-01, Vol.2018 (1)

2018

Volltextzugriff (PDF)

A generalized method aiming at predicting the polymer melt flow field in the metering zone of large-scale single-screw extruders

International journal of advanced manufacturing technology, 2024-05, Vol.132 (1-2), p.277-290

2024

Volltextzugriff (PDF)

Semi-analytical and numerical models to predict the extrusion force for silicone additive manufacturing, as a function of the process parameters

Additive manufacturing letters, 2023-07, Vol.6, p.100147, Article 100147

2023

Volltextzugriff (PDF)

An application- and market-oriented review on large format additive manufacturing, focusing on polymer pellet-based 3D printing

Progress in additive manufacturing, 2022-12, Vol.7 (6), p.1363-1377

2022

Volltextzugriff (PDF)

Compressive Properties of FDM Rapid Prototypes Treated with a Low Cost Chemical Finishing

Research Journal of Applied Sciences, Engineering and Technology, 2012-10, Vol.4 (19)

2012

Volltextzugriff (PDF)

Building a digital twin for additive manufacturing through the exploitation of blockchain: A case analysis of the aircraft industry

Computers in industry, 2019-08, Vol.109, p.134-152

2019

Volltextzugriff (PDF)

Investigating the Potential of Commercial-Grade Carbon Black-Filled TPU for the 3D Printing of Compressive Sensors

Micromachines (Basel), 2019-01, Vol.10 (1), p.46

2019

Volltextzugriff (PDF)

1 – 25 von 98

Suche als RSS-Feed

Suchergebnisse filtern

Filter anzeigen

Nur zeigen

Geprüft (Peer-Review)
(89)
Mit Volltextzugriff
(93)

Publikationsform

Sprache

Englisch
(98)
Japanisch
(2)

Erscheinungsjahr

n.n

Thema

Science & Technology
(76)
Technology
(51)
Engineering
(31)
Materials Science
(27)
Life Sciences & Biomedicine
(25)
Humans
(24)
Materials Science, Multidisciplinary
(24)
Additive Manufacturing
(23)
Engineering, Manufacturing
(20)
Female
(17)
Biological And Medical Sciences
(16)
Cardiovascular System & Cardiology
(16)
Medical Sciences
(16)
Cardiac & Cardiovascular Systems
(15)
Cardiology. Vascular System
(14)
Male
(14)
Fused Deposition Modeling
(13)
Instruments & Instrumentation
(13)
Middle Aged
(13)
Photogrammetry
(12)

15 weitere anzeigen...

Weniger anzeigen...

Menü

Weitere Dienste

Einstellungen

Assessment and Comparison of Various MCDM Approaches in the Selection of Manufacturing Process

Enhanced Solubility of the Support in an FDM-Based 3D Printed Structure Using Hydrogen Peroxide under Ultrasonication

Extrusion-Based 3D Printing of Microfluidic Devices for Chemical and Biomedical Applications: A Topical Review

Semi-analytical models for non-Newtonian fluids in tapered and cylindrical ducts, applied to the extrusion-based additive manufacturing

Fused filament fabrication of commercial conductive filaments: experimental study on the process parameters aimed at the minimization, repeatability and thermal characterization of electrical resistance

Additive Manufacturing for Soft Robotics: Design and Fabrication of Airtight, Monolithic Bending PneuNets with Embedded Air Connectors

Mechanobiological Approach to Design and Optimize Bone Tissue Scaffolds 3D Printed with Fused Deposition Modeling: A Feasibility Study

Analytical and Numerical Models of Thermoplastics: A Review Aimed to Pellet Extrusion-Based Additive Manufacturing

Thermal Characterization of New 3D-Printed Bendable, Coplanar Capacitive Sensors

Enhancing the sensitivity of 3D printed sensors via ironing and void reduction

Experimental investigation on camera calibration for 3D photogrammetric scanning of micro-features for micrometric resolution

On the Impact of the Fabrication Method on the Performance of 3D Printed Mixers

Manufacturing-oriented review on 3D printed lithium-ion batteries fabricated using material extrusion

Bioengineering Bone Tissue with 3D Printed Scaffolds in the Presence of Oligostilbenes

Correlation of Process Parameters with Mechanical Properties of Laser Sintered PA12 Parts

Fused Filament Fabrication (FFF) for Manufacturing of Microfluidic Micromixers: An Experimental Study on the Effect of Process Variables in Printed Microfluidic Micromixers

Additive manufacturing aimed to soft robots fabrication: A review

Additive Manufacturing for Sensors: Piezoresistive Strain Gauge with Temperature Compensation

Computer Numerical Controlled Grinding and Physical Vapor Deposition for Fused Deposition Modelled Workpieces

A generalized method aiming at predicting the polymer melt flow field in the metering zone of large-scale single-screw extruders

Semi-analytical and numerical models to predict the extrusion force for silicone additive manufacturing, as a function of the process parameters

An application- and market-oriented review on large format additive manufacturing, focusing on polymer pellet-based 3D printing

Compressive Properties of FDM Rapid Prototypes Treated with a Low Cost Chemical Finishing

Building a digital twin for additive manufacturing through the exploitation of blockchain: A case analysis of the aircraft industry

Investigating the Potential of Commercial-Grade Carbon Black-Filled TPU for the 3D Printing of Compressive Sensors

Suchergebnisse filtern