UB Paderborn / Katalog / Suche / in CDI

1 – 25 von 332

Sortiert nach

Influence of the focus offset on the defects, microstructure, and mechanical properties of an Inconel 718 superalloy fabricated by electron beam additive manufacturing

Journal of alloys and compounds, 2019-04, Vol.781, p.842-856

2019

Volltextzugriff (PDF)

Effect of Preheating Temperature on Microstructural and Mechanical Properties of Inconel 718 Fabricated by Selective Laser Melting

Metals and materials international, 2022-11, Vol.28 (11), p.2836-2848

2022

Volltextzugriff (PDF)

Role of strain-induced martensitic transformation on extrusion and intrusion formation during fatigue deformation of biomedical Co―Cr―Mo―N alloys

Acta materialia, 2014-12, Vol.81, p.377-385

2014

Volltextzugriff (PDF)

Collective behavior of strain-induced martensitic transformation (SIMT) in biomedical Co–Cr–Mo–N alloy polycrystal: An ex-situ electron backscattering diffraction study

Materials science & engineering. A, Structural materials : properties, microstructure and processing, 2014-08, Vol.611, p.263-273

2014

Volltextzugriff (PDF)

Thermodynamic analysis of oxygen refining during electron-beam additive manufacturing of pure titanium products

Materials letters, 2019-02, Vol.236, p.106-108

2019

Volltextzugriff (PDF)

Microstructural study on a Fe-10Cu alloy fabricated by selective laser melting for defect-free process optimization based on the energy density

Journal of materials research and technology, 2020-11, Vol.9 (6), p.12834-12839

2020

Volltextzugriff (PDF)

Strain-induced martensitic transformation near twin boundaries in a biomedical Co–Cr–Mo alloy with negative stacking fault energy

Acta materialia, 2013-03, Vol.61 (5), p.1648-1661

2013

Volltextzugriff (PDF)

Enhanced osseointegration of Ti6Al4V ELI screws built-up by electron beam additive manufacturing: An experimental study in rabbits

Applied surface science, 2020-04, Vol.508, p.145160, Article 145160

2020

Volltextzugriff (PDF)

Deformation mode in biomedical Co–27% Cr–5% Mo alloy consisting of a single hexagonal close-packed structure

Scripta materialia, 2010-11, Vol.63 (11), p.1092-1095

2010

Volltextzugriff (PDF)

Effect of electron beam continuity on microstructures and mechanical properties of titanium lattice structures produced with electron beam additive manufacturing

Materials & design, 2021-09, Vol.207, p.109822, Article 109822

2021

Volltextzugriff (PDF)

Physically Cross-Linked Homopolymer Ion Gels for High Performance Electrolyte-Gated Transistors

ACS applied materials & interfaces, 2017-03, Vol.9 (10), p.8813-8818

2017

Volltextzugriff (PDF)

Unidirectional columnar microstructure and its effect on the enhanced creep resistance of selective electron beam melted Inconel 718

Journal of alloys and compounds, 2020-03, Vol.817, p.153320, Article 153320

2020

Volltextzugriff (PDF)

Effect of cyclic heat treatment on commercially pure titanium part fabricated by electron beam additive manufacturing

Journal of alloys and compounds, 2019-08, Vol.796, p.300-306

2019

Volltextzugriff (PDF)

Improvement of mechanical properties of cast pure titanium by repeated heat treatment

Materials science and technology, 2019-02, Vol.35 (3), p.248-252

2019

Volltextzugriff (PDF)

Mechanical and microstructural characteristics of commercial purity titanium implants fabricated by electron-beam additive manufacturing

Materials letters, 2017-01, Vol.187, p.64-67

2017

Volltextzugriff (PDF)

Asymmetric slip trace formation in tension/compression cyclic deformation of biomedical Co–Cr–Mo–N alloy with negative stacking fault energy

Scripta materialia, 2014-03, Vol.74, p.52-55

2014

Volltextzugriff (PDF)

Fabrication of micro condenser tube through direct extrusion

Journal of materials processing technology, 2007-06, Vol.187, p.645-648

2007

Volltextzugriff (PDF)

Alloy design of Ni-based superalloy with high γ′ volume fraction suitable for additive manufacturing and its deformation behavior

Additive manufacturing, 2022-04, Vol.52, p.102680, Article 102680

2022

Volltextzugriff (PDF)

Influence of Aging Treatment on the Mechanical and Electrical Properties of Cu-0.5%Be Alloy

Journal of materials science & technology, 2008, Vol.24 (1), p.120-122

2008

Volltextzugriff (PDF)

Eco-Friendly Grain Refinement for A3003 Alloy

Materials science forum, 2009-01, Vol.620-622, p.89-92

2009

Volltextzugriff (PDF)

Effect of Annealing Atmosphere on the Mechanical Property of Free-cutting Phosphor Bronze Alloy

Journal of materials science & technology, 2008, Vol.24 (1), p.115-119

2008

Volltextzugriff (PDF)

Grain refinement mechanism in A3003 alloy

Journal of physics. Conference series, 2009-01, Vol.144 (1), p.012091

2009

Volltextzugriff (PDF)

Properties of binary TiO2-SiO2 composite particles with various structures prepared by vapor phase hydrolysis

Journal of materials science, 2003-09, Vol.38 (17), p.3545-3552

2003

Volltextzugriff (PDF)

Effect of Preheating Temperature on Microstructural and Mechanical Properties of Inconel 718 Fabricated by Selective Laser Melting

Metals and materials international, 2022-11, p.2836-2848

2022

Volltextzugriff (PDF)

Estimation of Energy Requirements and Atmospheric Emission in Continuous Casting Process for Al Wire

Materials science forum, 2009-01, Vol.620-622, p.81-84

2009

Volltextzugriff (PDF)

1 – 25 von 332

Suche als RSS-Feed

Suchergebnisse filtern

Filter anzeigen

Nur zeigen

Geprüft (Peer-Review)
(283)
Mit Volltextzugriff
(310)

Publikationsform

Sprache

Erscheinungsjahr

n.n

Thema

Science & Technology
(220)
Life Sciences & Biomedicine
(122)
Technology
(84)
Humans
(80)
Materials Science
(60)
Male
(46)
Physical Sciences
(45)
Materials Science, Multidisciplinary
(43)
Female
(40)
Chemistry
(30)
Engineering
(30)
Middle Aged
(29)
Science & Technology - Other Topics
(27)
Physics
(26)
Neurosciences & Neurology
(25)
Aged
(23)
Physics, Applied
(21)
Clinical Neurology
(20)
Patients
(20)
Animals
(19)

15 weitere anzeigen...

Weniger anzeigen...

Neu hinzugefügt

... seit 90 Tagen
(6)

Menü

Weitere Dienste

Einstellungen

Influence of the focus offset on the defects, microstructure, and mechanical properties of an Inconel 718 superalloy fabricated by electron beam additive manufacturing

Effect of Preheating Temperature on Microstructural and Mechanical Properties of Inconel 718 Fabricated by Selective Laser Melting

Role of strain-induced martensitic transformation on extrusion and intrusion formation during fatigue deformation of biomedical Co―Cr―Mo―N alloys

Collective behavior of strain-induced martensitic transformation (SIMT) in biomedical Co–Cr–Mo–N alloy polycrystal: An ex-situ electron backscattering diffraction study

Thermodynamic analysis of oxygen refining during electron-beam additive manufacturing of pure titanium products

Microstructural study on a Fe-10Cu alloy fabricated by selective laser melting for defect-free process optimization based on the energy density

Strain-induced martensitic transformation near twin boundaries in a biomedical Co–Cr–Mo alloy with negative stacking fault energy

Enhanced osseointegration of Ti6Al4V ELI screws built-up by electron beam additive manufacturing: An experimental study in rabbits

Deformation mode in biomedical Co–27% Cr–5% Mo alloy consisting of a single hexagonal close-packed structure

Effect of electron beam continuity on microstructures and mechanical properties of titanium lattice structures produced with electron beam additive manufacturing

Physically Cross-Linked Homopolymer Ion Gels for High Performance Electrolyte-Gated Transistors

Unidirectional columnar microstructure and its effect on the enhanced creep resistance of selective electron beam melted Inconel 718

Effect of cyclic heat treatment on commercially pure titanium part fabricated by electron beam additive manufacturing

Improvement of mechanical properties of cast pure titanium by repeated heat treatment

Mechanical and microstructural characteristics of commercial purity titanium implants fabricated by electron-beam additive manufacturing

Asymmetric slip trace formation in tension/compression cyclic deformation of biomedical Co–Cr–Mo–N alloy with negative stacking fault energy

Fabrication of micro condenser tube through direct extrusion

Alloy design of Ni-based superalloy with high γ′ volume fraction suitable for additive manufacturing and its deformation behavior

Influence of Aging Treatment on the Mechanical and Electrical Properties of Cu-0.5%Be Alloy

Eco-Friendly Grain Refinement for A3003 Alloy

Effect of Annealing Atmosphere on the Mechanical Property of Free-cutting Phosphor Bronze Alloy

Grain refinement mechanism in A3003 alloy

Properties of binary TiO2-SiO2 composite particles with various structures prepared by vapor phase hydrolysis

Effect of Preheating Temperature on Microstructural and Mechanical Properties of Inconel 718 Fabricated by Selective Laser Melting

Estimation of Energy Requirements and Atmospheric Emission in Continuous Casting Process for Al Wire

Suchergebnisse filtern